Model Overview & Print Notes
Summary
This is a wall mount I designed and made for the Meta Quest 3 VR Headset; I also made a wall mounts for the Quest 1 and 2 when they were released, (see my other designs) and was hoping to have this wall mount compatible with the Quest 1 and 2, but the design of the Quest 3 prohibits that. Note that this wall mount works fine with Elite Strap and with the Elite Strap with battery (the strap battery can be easily plugged in whilst on the wall mount.) I have added a 3.85 model for those who want to have the Elite Strap on backwards; but once again the normal mount works fine with the Elite Strap with battery. I have added three new STL files to make printing easier, one is a top part, and the other a bottom part, the third is a skinny top to fit on a tiny printer bed, even smaller bed if you put it on at a 45 degree angle; see in print section below.
*This has been tested and works with the 3S.
Like my other Quest wall mounts, this works well, but please be gentle with it as any damage to your headset is on you. I designed this to mount to a wall STUD with sheet rock / dry wall screws; (You can use on a piece of Wood or wall with the correct anchors MAKE SURE YOU DO NOT SCREW INTO A CABLE OR PIPE OF SOME KIND. IF YOU ARE NOT 100 PERCENT SURE WHAT TO DO, GET HELP INSTALLING THIS
The hook on the bottom is hold the USB C cable in place when the unit is not being charged.
Also, please checkout and subscribe to my YouTube channel, youtube.com/10p6
**** I have changed the license agreement for this model to allow remixes and sales with attribution for remixes per Thingverse rules.
The rules:
1 - Keep the 10p6 Logo (if you do not like it, do not do a remix). These models are protected under US and International law.
2 - DO NOT USE THE META LOGO AT ALL (That is a registered trademark and I do not want it on my models / remixes.)
3 - Make sure you list and link your remix to this model here on Thingiverse and nowhere else; (This is my model you are altering, not a model you are creating.)
4 - If I find my model files or remixes of it on any other site I will have them removed.
I have also allowed my model to be 'Printed' and sold online. Note that credit for any sale listing must show the model was designed by 10P6 and must not be made to look like you designed it. You are responsible for the quality of the prints, and any design changes made as I know my model works perfectly. DO NOT REMOVE THE 10P6 LOGO.
THESE MODIFIED LICENSES DO NOT ALLOW FOR THE ELECTRONIC DESIGN FILE/s, OR REMIXES TO BE SOLD OR SHARED ON ANY SITES OTHER THAN THINGIVERSE.
MY PHYSICALLY PRINTED MODEL AND YOUR REMIXES CAN BE SOLD ON OTHER SITES, HOWEVER DO NOT SELL ANY MODELS / REMIXES EITHER DIGITAL OR PRINTED ON CULTS3D AS THE OWNER THINKS COPYRIGHT THEFT IS OK WHICH IT IS NOT. ****
1st Amendment protected.
Print Settings
Printer:
IDEX
<p class="detail-setting resolution"><strong>Resolution: </strong> <div><p>High as possible</p></div></p> <p class="detail-setting infill"><strong>Infill: </strong> <div><p>25 percent - 100 percent with 3.85</p></div></p> <strong>Filament:</strong> eSun PLA+ (Pro) Any <br> <p class="detail-setting notes"><strong>Notes: </strong> </p><div><p>This is easy to print either flat or vertically. Use supports. I recommend using a minimum of 3 walls, 3 tops and 3 bottoms, and at least 25 percent infill (if you can, use 100 percent fill. I highly recommend 100 percent infill on the 3.85 models) I used 5 percent Zig Zag supports with Z offset for 0.2mm as this makes it really easy to remove supports, and I also used adaptive layers in CURA. On the two separate parts I have added, only the bottom part needs supports; I am not adding the 45 degree chamfer myself to this as it pushes up against the face foam on the unit.</p><p>With the two separate half's, technically they can print on a bed as small as 200 x 100 mm, but if you place them (one at a time) on the bed at 45 degree angle, you may get them to fit on a bed as small as 175 x175mm. </p><p>I have added a new top called 3.9 Skinny. This is 180mm across, but if put on a bed at a 45 degree angle then it can print on a bed as small as 153x153mm; or if you do a uniform scale in the slicer to 98.5 Percent, then it will fit on a 150x150 bed. NOTE THAT I HAVE NOT TESTED THIS PIECE, SO DO SO AT YOUR OWN RISK, AND MAKE SURE YOU DO 100 PERCENT INFILL ON THIS ONE. </p><p><strong><em> USE PLA+ (PRO) AS IT IS STRONGER AND NOT AS BRITTLE AS NORMAL PLA. </em></strong></p></div>
💬Thingiverse Community Comments(25)
★Thingiverse Original Reviews