Christmas Stocking Cookie Cutter and Stamp STL

Model Overview & Print Notes

Summary Make your own version free in your browser, any size or design: meshcast.app/cutter 100k+ makers follow us on Instagram for new free designs and casting tips: @meshcast.app A Christmas stocking cutter with a matching stamp that presses in the cuff, heel, toe and a star. About this design A classic Christmas stocking with a wide cuff, a rounded heel and the toe pointing right. The cutter cuts the outline and its stamp presses a border line, the cuff, the heel and toe patches and a small star into the dough, so the cookie is already drawn before it goes in the oven. Good for Christmas cookie boxes, advent baking, stocking fillers and name cookies for the Christmas table. The cookie comes out about 75 by 90 mm. Made with our free cookie cutter generator, not modelled by hand: we drew the shape with the stamp's lines inside it, uploaded it to the tool, set the cutter size to 90 mm and switched on Generate stamp. The STL in the zip is exactly what the tool gives you: the cutter (a 0.8 mm blade, 14 mm tall, with a 4 mm rim to press on) and, next to it, the stamp that drops inside the cutter and presses the lines into the cut cookie. Both print flat, with no supports. The drawing is in the zip too, as an SVG, so you can make both bigger or smaller. The cuff is left plain on purpose. Pipe a name on it once the icing has set and every stocking doubles as a place card or a personal gift. Shown as a 3D render of the printed cutter and stamp and two stamped cookies, not a photo. Made with Meshcast Meshcast is a free toolkit for makers that runs in your browser: turn any 3D model into a candle, soap, concrete or silicone mold, or make your own cookie cutters, texture rollers, stamps and keychains. Nothing to install, and you can try every tool without an account. Cookie Cutter Maker: meshcast.app/cutter Guide and print facts for this design: meshcast.app/3d-models/christmas-stocking-cookie-cutter 400+ ready-made molds and models: meshcast.app/3d-models Meshcast: https://meshcast.app/ Instagram: @meshcast.app How this was made The model is parametric: it is generated by Meshcast's own code, not made by an AI. The pictures are rendered in Blender. We use AI to assist our work (ideas, writing and checking), so this design carries Thingiverse's AI label to be on the safe side. Selling what you make? Free for personal use under CC BY-NC. Selling what you cast or print from this design needs a Meshcast commercial licence (Pro or Founder): meshcast.app/licenses Instructions Print settings Estimated from the file, not sliced, on the same basis as our sliced cutters (PrusaSlicer 2.7.2): 0.4 mm nozzle, 0.2 mm layers, 3 perimeters, 15% infill, MK3-class speeds. Cutter rim and stamp back flat on the bed, no supports. PLA or PETG. What you need Rolled cookie dough that holds its shape: sugar cookie, shortbread or gingerbread, with little or no baking powder A rolling pin, and two 5 to 6 mm guides for an even thickness Flour or cornflour for dusting the cutter and the stamp, and baking paper About 21 g of PLA or PETG, ideally a food-contact filament Steps Print the file as exported: the cutter rim flat on the bed with the blade pointing up, and the stamp beside it, no supports. Wash both parts in warm soapy water before the first use. Roll the chilled dough 5 to 6 mm thick between two sheets of baking paper. Dip the blade in flour, press straight down with your palm on the rim, and lift. Dust the stamp, press it pattern side down into each cut cookie about 2 mm deep, and lift it straight up. Chill the stamped cookies for ten minutes, then bake. Wash both parts by hand straight after use and let them dry. PLA softens in a dishwasher.