X2D/P2S/P1/X1 storage base - Space Expansion Series 《Tower Shield》

Model Overview & Print Notes

New Model Release Pixel Mega Bin | Pixel Style Stackable Large Capacity Storage Bin (Click the text link to view) "Tower" Stacking Shelf / Storage Rack (Click the text link to view) Update Log 2026.08.24 New addition: Following requests from comment section, added drawer storage compartments, uploaded under "accessory 9 - drawer storage compartment (not required to print)", this accessory includes 6 specifications (SP version is only for middle connection), everyone can print as needed, see the following images for details 2026.07.05 Update: waste chute iterated to version 3.0 , increased overall thickness of the chute, adjusted internal space, improved flow rate so as to enhance waste passability; the top of the outlet is changed to semi-open design, and its length is shortened to reduce the probability of outlet clogging, this update only applies to the built-in waste bin 2026.06.18 New addition: Following requests from comment section, added "large opening with large waste bin" version drawer, added to "accessory 8 - large opening with large waste bin", everyone who needs it can get it. At the same time thank you all for your continuous support, you are welcome to leave requests in the comment section, I will try my best to satisfy them 2026.06.05 Update New addition: Following requirements from comment section, added "build plate storage module", added to new profile — "accessory 7 - build plate storage module (standard version)", one standard storage module can hold 4 build plates, this module supports stacking multiple units, you can print as needed ( print parameters are built-in, no need to worry about parameter reset when switching printers, print with confidence ) 2026.05.22 Update Optimization: Modified classification logic of main body and accessories, renamed some accessories for clearer positioning and easier lookup and download Optimization: Saved latest parameters into the model objects, you no longer need to fill in parameters manually, parameter reset from switching printers will not affect printing 2026.05.20 Update Optimization: Adjusted parameters to fix stringing issues on hollowed sections, further improved printing stability with slightly longer print time Other: Following requirements from comment section, published key parameters for users who cannot find corresponding parameters to fill in manually, see the figure below (based on 0.2mm standard parameters, only lists parameters that need adjustment, unlisted parameters use default values directly) 2026.05.15 Update The issue that only one printer model can see the sliced files (3MF) has received an official reply, the problem has been fixed, now all printer models can see corresponding sliced files (3MF) 2026.05.12 Update Iteration: Built-in waste chute upgraded to version 2.0, this version keeps the same appearance while changing the inside of the chute to rounded corners, forming a slide shape to further reduce friction and make waste discharge smoother Optimization: Added 2 reinforcement ribs to the waste chute fixing holes, fixed the easy breakage issue near screw hole positions 2026.05.09 Update New addition: External waste bin, eliminates waste chute clogging, with observation slot to monitor waste level at any time; when using this assembly, do not print the lower half of the waste chute , also do not print drawers with built-in waste bin , just print two identical drawers without built-in waste bin Optimization: Integrated all assemblies into the same 3MF file Optimization: Optimized pre-plating description to avoid confusion Note: Tried uploading 3MF using X2D as default slicer machine, now only X2D can see download profiles, so no matter what printer you have, go to the "All" tab to download the 3MF file, the model includes all parts for all printer models, thank you for your understanding 2026.04.22 Profile Note Many users in the comment section reported that only P2S can see the print profile, users of X2D/X1/P1 cannot see them, I will reply uniformly here. The cause is currently unknown, users of other printer models can directly download the P2S version, the models are identical, just be careful not to reset parameters when switching printers, if parameters are already reset, please re-download and manually enter the parameters into your profile. There is no other solution for now, sorry   2026.03.20 Optimization and Fix Update: Optimized the opening position of the left drawer rear section and waste bin, avoids interference with drawer sliding when the waste chute outlet is extended Fix: Emergency fixed the length issue of the waste chute lower half in the v0318 version 2026.03.18 Integrated Waste System Optimization Update 1: Larger waste bin (1.5x capacity) and matching drawer, this version is suitable for users doing high intensity multi-color printing Update 2: Optimized the integrated waste chute system to make waste reach the bin more smoothly. The outlet is extended 10mm, the waste chute is thickened 5mm, and a 5mm small chamfer is added at the corner 2026.02.25 Now supports HULA feet Multiple users in the comment section asked for HULA foot compatibility, users who want to install HULA feet only need to attach the adapter to the bottom (you do not need to print my shock-absorbing feet if you use HULA feet)     2026.2.10 Fixed waste chute mismatch issue for P1/X1 Thanks for feedback from comment section, the waste chute length for P1/X1 did not match, the issue has been emergency fixed and reuploaded, you only need to reprint the shorter section, sorry 2026.02.02 Added a larger opening drawer Following suggestions from comment section, updated a larger opening drawer, already uploaded, users with thick fingers can try printing this version, only the front section is modified, the rear section uses the original version 2026.01.28 Waste chute matching P1S/X1E Updated waste chute matching P1S/X1E 2026.01.28 Compatibility with P1S/X1E and subsequent updates confirmed 1. Confirmed from support ticket that P2S and P1S/X1E have identical foot dimensions and hole spacing, so compatibility with P1S/X1E is confirmed, print with confidence 2. At the same time, after comparison, the waste discharge port positions of the 3 models are slightly different, I will update the matching waste chute soon, users of P1S/X1E please do not print the waste chute in the 3MF file for now 2026.01.27 Compatible with official external waste discharge of P2S Please re-download the 3MF file, do not print the waste chute of previous versions, the new chute only requires 1 screw, is compatible with official external discharge, uses less filament, and saves 4 magnets. The following is the main content Space Expansion Series — 《 Tower Shield 》 X2.P2.X1.P1 Storage Base officially released Highlight Introduction Supports X2D/P2S/P1/X1 Oversized space, stores everything Built-in waste chute, detachable waste bin Same TPU shock-absorbing feet as the printer body, ensures body stability no supports, zero waste Hardware only requires magnets (10mm diameter * 4mm thickness or 10mm diameter * 3.5mm thickness are both okay, 8 pieces) Very detailed manual, easy installation only requires glue Model Introduction The model consists of 5 parts: base, 2 oversized drawers, waste chute and TPU shock-absorbing feet Developed fully based on P2S, fits perfectly after installation I will provide detailed installation instructions, please read the printing instructions below carefully before printing Preview: I will release an active chamber temperature module for P2S later, the module will integrate the official left auxiliary fan and 220V 600W active chamber temperature control Printing Instructions This work includes many large models, although P2S is an enclosed printer, it does not have active chamber heating, there is still some warping risk in winter, I have adjusted the print parameters accordingly to avoid print failure, please do not change parameters arbitrarily TPU shock-absorbing feet are recommended to be printed with 85A or 90A for better results, currently default to 95A HF which is easier to print and has faster print speed. But 85A, 90A and 95A all work normally Default to print with PETG HF, if you are worried about warping you can also use PLA with lower sinkage rate, the printing cost will increase accordingly In addition to parameters, to avoid print failure as much as possible, please complete the following steps before printing Clean the build plate Apply glue Do not open the chamber door during printing Do not blindly increase filament cooling parameters Increase bed temperature by 5 degrees Ensure filament is dry (even newly opened filament should be dried first) Slight warping is okay, 1-2mm error will not affect assembly (don't be overly perfectionist, be kind to yourself) Finally attached real product photos, PDF version is available for download

Print profiles