Vario Lynx 1:8 external scale detail parts.

Model Overview & Print Notes

This is a list of many panel doublers and other scale detail for the Vario Lynx fuselage. Also check out my other Vario Lynx accessories: http://cults3d.com/en/various/replacement-nose-for-the-vario-lynx http://cults3d.com/en/various/vario-lynx-1-8-scale-cabin-and-cockpit-doors http://cults3d.com/en/various/vario-lynx-cockpit-interior http://cults3d.com/en/various/scale-helicopter-seats-westland-lynx-1-8-seats Lynxguide.zip - Photos showing the placement on my Lynx.Should be better wuality than the ones shown here. Wheellock01.stl - Dummy wheel locks for one main and one nose wheel. Wheel01-03 - Wheels and tires for the nose and main wheels. Antenna01.stl - Belly antenna and collector tank covers. Ice01.stl - Ice accretion indicator for right side under cockpit door. Pitot01.stl - Pitot tube. Flotation01.stl - Front flotation bags. Tiedown01.stl - Sponson tie down shackle. Tiedown02.stl - Nose tie down shackle. HF01.stl - Forward HF antenna with mounting base. Fuelvent01.stl - Fuel ventilation pipe. Sidestores01.stl - Bottom side stores eyelets and belly panels. Sidestores02.stl - Top side stores eyelets. Footstep01.stl - Fuselage side footsteps. Mainfuel01.stl - Main fuel tank panels and air intakes for aft compartment. Fuelcap01.stl - Main tank gravity fuel filling ports. Cockpitdoor01.stl - Dummy cockpit doors, handles and latch (for locking in open position). Wiper01.stl - Windshield wipers. Rooffairing01.stl - Extension for the bump between the roof windows. Requires adaptation and filling. Roofpanel01.stl - Panel in front of sliding fairing (doghouse). AC-intake01.stl - AC generator air intake for roof fairing front. Sliding01.stl - Rail stop in front of roof sliding fairing MGB-footstep01.stl - Dummy footstep panels. Collar01.stl - Filleted ring for blending the area around the main rotor. Nose03.stl - Douple panels for the joint between the nose and fuelage, bottom and top pieces. Panel01.stl - Panel doublers fuselage sides below engine cowlings. Panel02.stl - Panel doublers fuselage sides in front of tail joint. Panel04.stl - Panel doublers in front of and behind cockpit doors. Panel06.stl - Panel doublers fuselage sides along panel line. Panel11.stl - Inset panel under cabin doors. Navlight01.stl - Cockpit footsteps and nav light units. Extpower01.stl - External power panel. Fuelpanel01.stl - Fuel pressure filling access panel for right side. Aftcompartment01.stl - Aft compartment door. Nosegearfairing01.stl - Fairing that fits around the nose gear. Nosegearfairing02.stl - Same as above, but with larger hole if needed. Sponson01.stl - Root trailing edge fillets for the sponsons. Remove material to fit them. Exhaust01.stl - Shapes for creating filleted openings for the ducts. Exhaust02.stl - Exhaust ducts for 50 mm fan. Tailfairing01.stl - Covers between exhaust duct fairings. Intake01.stl - Engine air intake leading edge and detail parts. Coolerintakes01.stl - Engine oil cooler and accessories cooler intakes. Engcowllock01.stl - Guides for wire lock on the top between the engine cowlings. Bump01.stl - Bumps and doublers for the engine cowlings. Enghandle01.stl - Engine cowling locking handles and bump stops. IGB01.stl - Tail intermediate gearbox fairing parts. Tailplane01.stl - Shortened tail plane with gourney flap. Shaftcover01.stl - Tail drive shaft cover doublers. Glue over the tail shaft bump on the tail. Trailingedge01.stl - Access panels for the left side of the tail fin trailing edge fairing. Tailpanel01.stl - Lifting holes and doublers for the tail boom. Tailpanel02.stl - Tail fish plate and tail fin doublers for left side. Tailpanel03.stl - Tail fish plate and tail fin doublers for right side. Tailpanel04.stl - Overlapping panel for the tail boom. Tailpanel05.stl - Overlapping panel for the tail boom. Trim length to fit in the rear. Tailpanel06.stl - Overlapping panel for the tail boom. Trim length to fit in the rear. Antenna02.stl - Tail boom bottom center antenna. HF02.stl - Middle and rear HF antenna posts. Anticollision01.stl - Anti collision lights for the top of the tail. ## 3D Printing Settings Print as they open. I usually print small parts with 100% infill.

Files (60)